How to Install a Bath Tub
How to Install a Bath Tub
Blog Article
How do you really feel when it comes to How to Install a Bathtub?
Mounting a bath tub isn't specifically brain surgery, however it does need strong plumbing, carpentry, as well as in some cases, tiling skills. Replacing an old bathtub with a new one is also a reasonably hard task. If the old tub is easily available, the project can move speedily; if you need to open up a wall surface to remove the old tub and place the brand-new tub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will need an assistant to vacate the old bathtub as well as set in the brand-new one. See to it you have actually qualified on your own for the work as well as are comfortable attempting it. As opposed to working with a specialist to take over a halfway-completed project, it is far better to take into consideration employing one prior to you start. Possibilities are you may require an expert plumber to make tube connections.
This article will certainly assist you install a brand-new bathtub in your washroom if you have currently gotten a new bathtub and do not need to transform the arrangement of your previous water pipes.
Your tools and also material list must make up the following:
Preparing for the Installment
Firstly, the sustaining frame provided with the bath should be fitted (if needed) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to make certain that if the tap includes a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps device to prevent pressure on the bathtub.
Fit the versatile tap ports to the bottom of both taps making use of 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its last position.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the taps to drain any type of water staying in the system. The procedure of getting rid of the existing faucets can be fairly bothersome because of the restricted gain access to that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a fabric prepared for the staying water that will come from the pipes. Once the supply pipes have been gotten rid of, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Before going on to fit the brand-new faucets, contrast the pipe connections on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bathtub
Using both wood boards under its feet, put the bathtub in the required placement. The wood boards are practical in evenly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 tiny points.
The next objective is to make sure that the tub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bath tub up until the spirit level reads level.
To install faucets, fit the bottom of the furthest adaptable faucet connector to the ideal supply pipeline by making a compression join; after that do the exact same for the other faucet.
Turn on the supply of water and also inspect all joints and brand-new pipework for leaks and tighten them if essential. Fill up the bathtub as well as also examine the overflow electrical outlet and the regular outlet for leakages.
Lastly, deal with the bath paneling as described in the maker's instruction manual. Tiling and also sealing around the bath tub must wait until the tub has been made use of at least when as this will resolve it into its last position.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin making certain that the washers remain in area between the faucet and the sink. Protect the faucet in place with the producer given backnut. Once the faucet is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind should be linked to the faucet ends first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to split an inflexible seal, causing the water to penetrate the wall in between the bath and the tiling, causing issues with wetness and also possible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your components and fittings. They are sold in tubes as well as cartridges, as well as can securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealer can crack fairly early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the market. It is advisable to fit the tiles making use of waterproof or water-proof glue and also cement.
Bathtub Installation
How Important Is A Bathtub To Your Home?
High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.
Install Piping Before Tub
You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.
Position the Tub
Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.
NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.
Assemble Drain Connections
Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.
Place a Pipe For the Shower Head
First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.
Attaching Hot and Cold Water Lines
Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.
Install the Spout
Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.
NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.
Check For Leaks
Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.
estore the Bathroom Wall
Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.
https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/
I came across that blog posting on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when scouting around the web. Liked our write up? Please share it. Help somebody else check it out. Thank you so much for going through it.
Try Here Report this page